How to use smoke detectors properly

 

Smoke Detector Services

Smoke detectors should be installed on every level of your home. Make sure to put them in the basement, the attic and include one in each bedroom.

One of the most important safety devices in your home is the smoke detector.  At Electrician Network , our certified technicians will work to ensure proper placement and installation of smoke detectors in your home.  These smoke detectors can be standalone and simply provide an audible alarm if smoke is detected or they can be wired into most home security systems to alert authorities if smoke is detected in your home.  In the Florida, it is required that smoke detectors are installed on every habitable level and in attics that are accessible, and within the vicinity of all bedrooms.

All of our skilled technicians at Electrician Network  who work in your home or business are professionally trained, background checked and drug tested.  Our technicians also drive fully stocked trucks to ensure they are able to get the job done the first time out to your home or business.

Carbon Monoxide Detectors

Carbon monoxide poisoning can be a serious threat to your health. Of all of the poisoning death causes in the United States, carbon monoxide poisoning is one of the most common. If undetected, this leaking gas can kill an entire family in a matter of hours or minutes. Because it lacks color, taste, and odor, it is among the most dangerous home hazards—however, carbon monoxide poisoning is 100% preventable with a detector. Installing reputable carbon monoxide detectors can be the literal difference between life and death.

Some of the most common systems within a home can release carbon monoxide, including:

Gas range

Stove

Gas clothes dryer

Water heater

Furnace

Gas or wood fireplace

Space heaters

Car exhaust

Charcoal grills

Clogged chimneys or flues

It's important to install carbon monoxide detectors properly on every floor of your home and outside every bedroom.

how to install and wire a smoke detector

Choosing a Location

Check with local codes for the number of alarms required for your home and their placement. When learning how to install a smoke detector, it’s important that they be installed in the proper locations in your home.

• Smoke rises, so the ideal location for a detector is on the ceiling. Mounting it in the center of the ceiling is best. If it needs to be mounted elsewhere on the ceiling, it must be at least 4 inches from a wall.
• Avoid corners where the walls meet the ceiling, and where pockets of dead air sometimes form, preventing rising smoke from reaching the detector.
• Wall-mounted detectors must be installed at least 4 inches from the ceiling to avoid this dead air zone.
• If you have vaulted ceilings, dead air can also form at the apex. Install the alarm at least 4 inches from the peak.
• Don’t place smoke detectors over stoves, ovens, clothes dryers or in areas where there is the potential for significant heat or steam generation.  

Types of Smoke Detectors

Smoke alarms will sound when they detect smoke. You can get smoke alarms that are specifically designed for different areas of your home.

Bedroom alarms typically feature a 10-year lithium ion battery, so you’ll never be awakened by a low-battery chirping sound in the middle of the night. Some units also feature a voice alarm to help raise you from your sleep.

Kitchen-specific alarms can detect both smoke and carbon monoxide. They are designed to detect real fires faster and trigger fewer nuisance alarms.

A smoke detector can be hard-wired or battery-powered.

Hardwired smoke detectors are powered directly to an AC electrical circuit, which is standard in new construction. Many also include a battery backup system to keep it functioning during power outages. One benefit of most smoke detectors is that they include a hush feature, which temporarily silences the smoke detector's alarm.

Battery smoke detectors are standalone and don’t require electrical wiring. They can use a nine volt or AA battery, which should be changed twice per year. Models with lithium batteries can last up to 10 years.

Plug-in CO alarms plug directly into an electrical wall outlet. The plug-in design isn’t practical for smoke alarms, but works for CO alarms.

Most smoke alarms come with a mounting base that separates from the alarm itself. This base will have key-shaped screw holes to allow you to fasten the base to a wall or ceiling.

How to Install Hardwired Smoke Alarms

A hard-wired smoke alarm or carbon monoxide alarm is connected to other detectors throughout your home. These alarms sound simultaneously, on all levels of your home, when a single unit detects smoke or gas. All the units are wired to a 120-volt household electrical circuit and each have a battery backup. The battery backup provides extra protection by powering the alarm even if a fire causes the household power to go out. It's important to learn how to install a hard-wired smoke detector yourself.

Install Remodeling Boxes

To prepare the wiring for an alarm in a new location, you need to install a remodeling box. A remodeling box is an electrical box that can be installed into drywall. This is one of the first steps to learn how to wire a smoke detector.

Identify where the smoke alarm will be installed. This can either be on the ceiling or on the wall 12 inches down from the ceiling.  

Use a stud finder to determine the location of wall studs around each alarm location.  

Use a marking tool to trace the outline of the wall remodeling box or ceiling remodeling box. Use a level to make sure the box outline is straight.  

Drill a 1/2-inch starter hole at the corner of your outline.  

Starting at the hole, cut along the outline of the shape with a drywall saw.  

Test-fit the remodeling box. It should fit into the hole snuggly. It should not fit so tightly that you have to force it. Do not set the remodel box yet.  

Repeat this process at each location where a smoke alarm will be installed.

Run Cable to Boxes

• Run 14-2 NM cable (a sheathed cable with 2 wires and a ground wire) from the house breaker panel to the smoke alarm closest to the breaker panel. Do not connect the cable to the breaker panel yet. You’ll do this at the end of the project.  
• When the cable reaches the alarm location, pull about 10 inches of the cable through the knockout of the first remodeling box.
• Run cable from the first knockout to the second knockout, leaving 10 inches of cable hanging out of the work box. Repeat this step until all remodeling box knockouts are connected by cable.

Secure Boxes

Use wire strippers to strip the sheathing off the NM cable to expose the inner wires.

• Insert the wires through the back of the remodeling box.
• Insert the box into the hole in the drywall.
• Screw down the clamping tabs carefully until the box is tight against the wall.
• Attach the copper wires (ground wires) to the box with a ground screw or with the box’s internal clamp, depending on the model.  

Connect Wires

• Use wire strippers to strip 3/4-inch of insulation from the ends of the wires.
• Connect the wires to a 120-volt wire harness. Usually the hard-wire smoke alarm comes with a quick connect wire harness.
• When connecting the wire harness, use wire nuts to connect the stripped NM cable wires to the same color harness wires. White wires connect to the harness’s white wire and red wires connect to the harness’s red wires.
• Only connect wires of like colors.
• When connecting smoke alarms to each other, the wire harness should connect to both the wires that run from the breaker panel (power source) and the wires that run between both alarms.
• Wrap the wire connectors with electrical tape for extra protection.  
• Gently tuck the excess wire length and wire connectors into the remodeling box. Leave the plug-end of the wire harness out.

Install Backup Battery

• Feed the wire harness through the smoke alarm mounting plate.  
• Place the alarm’s mounting plate on the remodel box and align the screw holes. Make sure the wire connection runs through the mounting plate.  
• Use the included screws to connect the mounting plate to the remodeling box.
• Plug the wire harness into the back of the smoke alarm.
• Open the battery compartment on the alarm.  
• Insert the correct type of battery (usually a 9-volt battery), being careful to position it so positive contact meets positive contact and negative contact meets negative.  
• Close the battery compartment.  

Attach Smoke Detector to Mounting Plate

• Line up the notches on the back of the alarm with those on the base.  
• Twist the alarm until it locks into place.  
• Check the connection to ensure it is secure on all sides. Once secured, you've successfully learned how to replace a smoke detector.
• Connect the other end of the NM cable to the beaker panel. Or hire an experienced electrician to complete this final step for you.

Test Smoke Detector

• Once all the wiring is connected at the breaker panel and no one is doing anymore electrical work, turn on the power to the circuit.  
• Confirm each alarm’s power light is on.  
• Press the test button on each alarm. You should be able to hear all the alarms each test.  
• If the alarms don’t sound, turn off the power at the breaker panel and double-check your wiring connections. If the connections are correct but a unit’s power light won’t come on, replace the unit.
•  
•